Entreq Logo
Connection guides

Connection Guides

Getting started with Entreq grounding in your set-up can seem daunting and our recommendation is always to speak to your local dealer to get the best advice for your system.

The process of adding grounding to your system is very much about trial. Whilst there are rules and best practices, there are no definitive answers as to what will work best with your specific equipment in your own  listening environment. Finding the sweet spot is all part of the experience.

There is, however, a general process to follow. This is about reducing noise in your signal chain. How far you take this process is down to personal preference and, as mentioned above, trialling what works best in your system.

Below we feature some of the basic configurations to give you a beginners guide to our range of grounding products.

Home / Support / Connection Guides

The Three Key Grounding Types

There are three key ways that we can perform grounding with Entreq ground boxes in an audio system, these are;

Each of these three grounding types can be used individually or together.


Negative Terminal Grounding

The act of grounding the negative terminals of your speakers is one of the most significant and effective ways to reduce unwanted noise within your system. It is important to note that this particular technique is only possible using Entreq ground boxes.

Why do it?

By grounding the negative terminals we can effectively draw away high-frequency noise from the signal before it feeds back into the amplifier. Removing noise from this signal path is one of the best places to start.

How to do it

To get started with negative terminal grounding you will need two Entreq ground boxes and two Eartha ground cables. Our Macro Twin Kit is a great place to start and comes complete with everything required, including a pair of dedicated spade to 4mm (banana plug) Eartha cables. This is the most cost-effective way to introduce Negative Terminal Grounding to your set-up.

  1. Make sure all equipment is powered down and disconnected from the mains.
  2. Fix the Eartha cable to the negative speaker output of the left-hand channel at the amplifier using the opposite configuration to your existing speaker cable (e.g. If your speakers are connected to your amplifier via spade connectors, connect the banana plug termination of your ground cable to the amplifier .
  3. Connect the other end of the Eartha cable to an Entreq ground box.
  4. Now repeat step 2 for the right-hand channel.
  5. Connect the other end of this Eartha cable to another, separate Entreq ground box.

WARNING: You must never connect both negative terminals to the same ground box unless you are using a multi-cell ground box in which case you must ensure that each negative terminal is connected to it’s own unique cell within the box. Connecting two negative speaker terminals to one ground box will damage your equipment.

Please note: this method of connection is optimal in the majority of scenarios. However, where space is at a premium or connection is not possible at the amplifier, the connection can be made from the negative terminals at the speakers themselves to the ground boxes. As always, we recommend seeking advice from your local dealer.


Signal grounding

Signal grounding is the act of connecting the common signal ground to an Entreq ground box.

Why do it?

All electronics produce RF that is detrimental to performance. Signal grounding is a very effective way to remove this unwanted noise and interference contained within the internal signal path.

How to do it

Simply connect any spare termination on your equipment to an Entreq ground box via your Eartha ground cable.

You can ground as many components as you wish and how far you go will be down to personal preference.

Our main recommendation is that the analogue components are grounded to separate boxes from digital components.

The diagram below outlines a common configuration of a system comprising a CD transport, DAC and integrated amplifier. We use three Eartha ground cables connected to three separate ground boxes. Note that if you have a muti-cell ground box, for example, the Tellus 3 Tungsten, then you can use each post on the ground box to achieve the same set-up.

  1. Make sure all equipment is powered down and disconnected from the mains.
  2. For each component you wish to ground, connect one Eartha cable to one of the spare terminations on the component.
  3. Connect the other end of this Eartha cable to an Entreq ground box.
  4. Repeat steps 2 & 3 for each component you wish to ground in your system.

WARNING: Do not connect any inputs – analogue or digital – to a ground box that is being used for negative speaker terminal grounding. This could damage your equipment.


EEDS Cable Grounding

Our EEDS technology removes unwanted RF and EMI from the signal as it passes through the cable. You can find out more about EEDS here.

Why do it?

Cables, as with all components in an audio system, can introduce RFI and EMI to the signal path. This is down to construction, materials and the naturally occurring capacitance along any length of conductor pairs. EEDS provides a dedicated conductor that wraps around the positive and negative conductors in the cable. We connect this EEDS wire to an Entreq ground box to drain away this noise.

How to do it

We connect the EEDS wire at the source end of the connection. For example, with speaker wires this would be at the amplifier, for a digital cable connecting a CD transport to a DAC, this would be at the CD Transport end.

  1. Make sure all equipment is powered down and disconnected from the mains.
  2. Take the end of the cable which includes the EEDS and connect the signal cable to the appropriate output.
  3. Now connect the EEDS drain wire to an Entreq ground box.
  4. Connect the other end of the signal cable to the receiver component.
  5. Repeat steps 2 to 4 for each signal cable with EEDS in your system.